Dyes, liquid, corrosive, n.o.s. or Dye intermediates, liquid, corrosive, n.o.s

Data from the Hazardous Materials Table

Source: 49 CFR §172 (2018/07)

Packing Group I
Packing Group II
Packing Group III

(3) Hazard Class

This entry is signed with "G". The letter "G" identifies proper shipping names for which one or more technical names of the hazardous material must be entered in parentheses, in association with the basic description. (See §172.203(k)).

(7) Special Provisions (§172.102)

×Note:
Special provisions may be very complex. The extracts are taken from 49 CFR §172.102. Please be careful with the information, as necessary, additional conditions may be applied that are not written here. Please check the original source and report bugs.

11	The hazardous material must be packaged as either a liquid or a solid, as appropriate, depending on its physical form at 55 °C (131 °F) at atmospheric pressure. Browse special provision 11
A6	For combination packagings, if plastic inner packagings are used, they must be packed in tightly closed metal receptacles before packing in outer packagings. Browse special provision A6
B10	MC 300, MC 301, MC 302, MC 303, MC 305, and MC 306 and DOT 406 cargo tanks, and DOT 57 portable tanks are not authorized. Browse special provision B10
T14	see 49 CFR §172.102
TP2	a. The maximum degree of filling must not exceed the degree of filling determined by the following: Where: t_r is the maximum mean bulk temperature during transport, t_f is the temperature in degrees celsius of the liquid during filling, and α is the mean coefficient of cubical expansion of the liquid between the mean temperature of the liquid during filling (t_f) and the maximum mean bulk temperature during transportation (t_r) both in degrees celsius. b. For liquids transported under ambient conditions α may be calculated using the formula: Where: d₁₅ and d₅₀ are the densities (in units of mass per unit volume) of the liquid at 15 °C (59 °F) and 50 °C (122 °F), respectively. Browse special provision TP2
TP27	A portable tank having a minimum test pressure of 4 bar (400 kPa) may be used provided the calculated test pressure is 4 bar or less based on the MAWP of the hazardous material, as defined in §178.275 of this subchapter, where the test pressure is 1.5 times the MAWP. Browse special provision TP27

(8) Packing Authorizations (§173.***)

(8A) Exceptions	None
(8B) Non-bulk	201	see 49 CFR §173.201
(8C) Bulk	243	see 49 CFR §173.243

(9) Quantity Limits

(9A) Passenger aircraft/rail	0.5 L
(9B) Cargo aircraft only	2.5 L

(10) Vessel stowage

(10A) Location	A Stowage category “A” means the material may be stowed “on deck” or “under deck” on a cargo vessel or on a passenger vessel. Source: 49 CFR §172.101(k)
(10B) Other	n/a

(3) Hazard Class

8
Corrosive liquids

(4) Identification number

UN 2801

(5) Packing Group

Comparison View of PG

(6) Labels

(1) Symbols

(7) Special Provisions (§172.102)

11	The hazardous material must be packaged as either a liquid or a solid, as appropriate, depending on its physical form at 55 °C (131 °F) at atmospheric pressure. Browse special provision 11
B2	MC 300, MC 301, MC 302, MC 303, MC 305, and MC 306 and DOT 406 cargo tanks are not authorized. Browse special provision B2
IB2	Authorized IBCs: Metal (31A, 31B and 31N); Rigid plastics (31H1 and 31H2); Composite (31HZ1). Additional Requirement: Only liquids with a vapor pressure less than or equal to 110 kPa at 50 [deg]C (1.1 bar at 122 [deg]F), or 130 kPa at 55 [deg]C (1.3 bar at 131 [deg]F) are authorized. Browse special provision IB2
T11	see 49 CFR §172.102
TP2	a. The maximum degree of filling must not exceed the degree of filling determined by the following: Where: t_r is the maximum mean bulk temperature during transport, t_f is the temperature in degrees celsius of the liquid during filling, and α is the mean coefficient of cubical expansion of the liquid between the mean temperature of the liquid during filling (t_f) and the maximum mean bulk temperature during transportation (t_r) both in degrees celsius. b. For liquids transported under ambient conditions α may be calculated using the formula: Where: d₁₅ and d₅₀ are the densities (in units of mass per unit volume) of the liquid at 15 °C (59 °F) and 50 °C (122 °F), respectively. Browse special provision TP2
TP27	A portable tank having a minimum test pressure of 4 bar (400 kPa) may be used provided the calculated test pressure is 4 bar or less based on the MAWP of the hazardous material, as defined in §178.275 of this subchapter, where the test pressure is 1.5 times the MAWP. Browse special provision TP27

(8) Packing Authorizations (§173.***)

(8A) Exceptions	154	see 49 CFR §173.154
(8B) Non-bulk	202	see 49 CFR §173.202
(8C) Bulk	242	see 49 CFR §173.242

(9) Quantity Limits

(9A) Passenger aircraft/rail	1 L
(9B) Cargo aircraft only	30 L

(10) Vessel stowage

(10A) Location	A Stowage category “A” means the material may be stowed “on deck” or “under deck” on a cargo vessel or on a passenger vessel. Source: 49 CFR §172.101(k)
(10B) Other	n/a

(3) Hazard Class

8
Corrosive liquids

(4) Identification number

UN 2801

(5) Packing Group

III

Comparison View of PG

(6) Labels

(1) Symbols

(7) Special Provisions (§172.102)

11	The hazardous material must be packaged as either a liquid or a solid, as appropriate, depending on its physical form at 55 °C (131 °F) at atmospheric pressure. Browse special provision 11
IB3	Authorized IBCs: Metal (31A, 31B and 31N); Rigid plastics (31H1 and 31H2); Composite (31HZ1 and 31HA2, 31HB2, 31HN2, 31HD2 and 31HH2). Additional Requirement: Only liquids with a vapor pressure less than or equal to 110 kPa at 50 [deg]C (1.1 bar at 122 [deg]F), or 130 kPa at 55 [deg]C (1.3 bar at 131 [deg]F) are authorized, except for UN2672 (also see Special Provision IP8 for UN2672). Browse special provision IB3
T7	see 49 CFR §172.102
TP1	The maximum degree of filling must not exceed the degree of filling determined by the following: Where: t_r is the maximum mean bulk temperature during transport, and t_f is the temperature in degrees celsius of the liquid during filling. Browse special provision TP1
TP28	A portable tank having a minimum test pressure of 2.65 bar (265 kPa) may be used provided the calculated test pressure is 2.65 bar or less based on the MAWP of the hazardous material, as defined in §178.275 of this subchapter, where the test pressure is 1.5 times the MAWP. Browse special provision TP28

(8) Packing Authorizations (§173.***)

(8A) Exceptions	154	see 49 CFR §173.154
(8B) Non-bulk	203	see 49 CFR §173.203
(8C) Bulk	241	see 49 CFR §173.241

(9) Quantity Limits

(9A) Passenger aircraft/rail	5 L
(9B) Cargo aircraft only	60 L

(10) Vessel stowage

(10A) Location	A Stowage category “A” means the material may be stowed “on deck” or “under deck” on a cargo vessel or on a passenger vessel. Source: 49 CFR §172.101(k)
(10B) Other	n/a

Comparison View of Different Packing Groups

More than one packing group is indicated for this entry. Criteria for assignment see 49 CFR §173 Subpart D. You can find specific details in the tabs above. Differences are highlighted.

	PG I	PG II	PG III
1	G	G	G
2	Dyes, liquid, corrosive, n.o.s. or Dye intermediates, liquid, corrosive, n.o.s	Dyes, liquid, corrosive, n.o.s. or Dye intermediates, liquid, corrosive, n.o.s	Dyes, liquid, corrosive, n.o.s. or Dye intermediates, liquid, corrosive, n.o.s
3	8	8	8
4	UN 2801	UN 2801	UN 2801
5	I	II	III
6	8	8	8
7	11, A6, B10, T14, TP2, TP27	11, B2, IB2, T11, TP2, TP27	11, IB3, T7, TP1, TP28
8A	None	154	154
8B	201	202	203
8C	243	242	241
9A	0.5 L	1 L	5 L
9B	2.5 L	30 L	60 L
10A	A	A	A
10B	n/a	n/a	n/a

Segregation Chart for Load, Transport, Storage

In this table a statement is contained for each hazard class whether the loading, transport or storage with other hazard classes is allowed, is not permitted or is restricted. The table is based on U.S.-Code 49 CFR §177.848.

Note: In this segregation and separation chart are HazMat of hazard class 8 considered depending if there are liquid. Currently HazMat Tool is not able to to check if a HazMat is liquid or not. Therefore it is assumed as liquid. See PHMSA Interpretation #09-0252.

Hazard Class	8	7	6.1	5.2	5.1	4.3	4.2	4.1	3	2.3B	2.3A	2.2	2.1	1.6	1.5	1.4	1.3	1.1/1.2
1.1/1.2
1.3
1.4
1.5
1.6
2.1
2.2
2.3A
2.3B
3
4.1
4.2
4.3
5.1
5.2
6.1
7
8

	May not be loaded, transported, or stored together in the same transport vehicle or storage facility.
	Load, transport, storage together is not restricted.
	Load, transport, storage together is allowed under restrictions.

Substances with similar name

UN-Number	Name	Hazard Class
UN 3206	Alkali metal alcoholates, self-heating, corrosive, n.o.s	4.2
	Aluminum phosphate solution, see Corrosive liquids, etc
	Bis (Aminopropyl) piperazine, see Corrosive liquid, n.o.s.
UN 3505	Chemical under pressure, flammable, corrosive, n.o.s	2.1
UN 2742	Chloroformates, toxic, corrosive, flammable, n.o.s.	6.1
UN 2987	Chlorosilanes, corrosive, n.o.s	8
UN 3362	Chlorosilanes, toxic, corrosive, flammable, n.o.s	6.1
UN 3264	Corrosive liquid, acidic, inorganic, n.o.s	8
UN 3265	Corrosive liquid, acidic, organic, n.o.s	8
UN 3266	Corrosive liquid, basic, inorganic, n.o.s	8
UN 3301	Corrosive liquid, self-heating, n.o.s.	8
UN 2920	Corrosive liquids, flammable, n.o.s.	8
UN 1760	Corrosive liquids, n.o.s.	8
UN 2922	Corrosive liquids, toxic, n.o.s.	8
UN 3263	Corrosive solid, basic, organic, n.o.s.	8
UN 2921	Corrosive solids, flammable, n.o.s.	8
UN 1759	Corrosive solids, n.o.s.	8
UN 2923	Corrosive solids, toxic, n.o.s	8
UN 1774	Fire extinguisher charges, corrosive liquid	8
UN 3180	Flammable solid, corrosive, inorganic, n.o.s.	4.1
UN 2925	Flammable solids, corrosive, organic, n.o.s.	4.1
	Isopentanoic acid, see Corrosive liquids, n.o.s.
UN 3098	Oxidizing liquid, corrosive, n.o.s	5.1
UN 3085	Oxidizing solid, corrosive, n.o.s	5.1
UN 3185	Self-heating liquid, corrosive, organic, n.o.s	4.2