Phosphorus, white dry or Phosphorus, white, under water or Phosphorus white, in solution or Phosphorus, yellow dry or Phosphorus, yellow, under water or Phosphorus, yellow, in solution

Phosphorus is a chemical element; it has symbol P and atomic number 15. Elemental phosphorus exists in two major forms, white phosphorus and red phosphorus, but because it is highly reactive, phosphorus is never found as a free element on Earth. It has a concentration in the Earth's crust of about one gram per kilogram (compare copper at about 0.06 grams). In minerals, phosphorus generally occurs as phosphate. Elemental phosphorus was first isolated as white phosphorus in 1669. Wikipedia

Substance Data

Data from the Hazardous Materials Table

(3) Hazard Class 4.2 Spontaneously combustible materials	(4) Identification number UN 1381	(5) Packing Group I
(6) Labels
(7) Special Provisions (§172.102) ×Note: Special provisions may be very complex. The extracts are taken from 49 CFR §172.102. Please be careful with the information, as necessary, additional conditions may be applied that are not written here. Please check the original source and report bugs. B9 Bottom outlets are not authorized. Browse special provision B9 B26 Tanks must be insulated. Insulation must be at least 100 mm (3.9 inches) except that the insulation thickness may be reduced to 51 mm (2 inches) over the exterior heater coils. Interior heating coils are not authorized. The packaging may not be loaded with a material outside of the packaging's design temperature range. In addition, the material also must be covered with an inert gas or the container must be filled with water to the tank's capacity. After unloading, the residual material also must be covered with an inert gas or the container must be filled with water to the tank's capacity. Browse special provision B26 N34 Aluminum construction materials are not authorized for any part of a packaging which is normally in contact with the hazardous material. Browse special provision N34 T9 see 49 CFR §172.102 TP3 The maximum degree of filling (in %) for solids transported above their melting points and for elevated temperature liquids shall be determined by the following: Where: df and dr are the mean densities of the liquid at the mean temperature of the liquid during filling and the maximum mean bulk temperature during transport respectively. Browse special provision TP3 TP31 This hazardous material may only be transported in tanks in the solid state. Browse special provision TP31 W31 see 49 CFR §172.102
(8) Packing Authorizations (§173.***) (8A) Exceptions None (8B) Non-bulk 188 see 49 CFR §173.188 (8C) Bulk 243 see 49 CFR §173.243
(9) Quantity Limits (9A) Passenger aircraft/rail Forbidden (9B) Cargo aircraft only Forbidden
(10) Vessel stowage (10A) Location E Stowage category “E” means the material may be stowed “on deck” or “under deck” on a cargo vessel or on a passenger vessel carrying a number of passengers limited to not more than the larger of 25 passengers, or one passenger per each 3 m of overall vessel length, but is prohibited from carriage on a passenger vessel in which the limiting number of passengers is exceeded. Source: 49 CFR §172.101(k) (10B) Other n/a

Segregation Chart for Load, Transport, Storage

In this table a statement is contained for each hazard class whether the loading, transport or storage with other hazard classes is allowed, is not permitted or is restricted. The table is based on U.S.-Code 49 CFR §177.848.

Add to my HazMat

Hazard Class	8	7	6.1	5.2	5.1	4.3	4.2	4.1	3	2.3B	2.3A	2.2	2.1	1.6	1.5	1.4	1.3	1.1/1.2
1.1/1.2
1.3
1.4
1.5
1.6
2.1
2.2
2.3A
2.3B
3
4.1
4.2
4.3
5.1
5.2
6.1
7
8

	May not be loaded, transported, or stored together in the same transport vehicle or storage facility.
	Load, transport, storage together is not restricted.
	Load, transport, storage together is allowed under restrictions.