HazMat Tool — substance information

Sodium hydrosulfide with not less than 25 percent water of crystallization

HMT 15 June 2026

UN / ID: UN 2949
Hazard class: 8
Packing group: II
ERG guide: ERG 154
Special provisions: SP A7, SP IB8, SP IP2, SP IP4, SP T7, SP TP2
Source: 49 CFR §172 (15 June 2026)

Spot an error in this entry?

On this page

Sodium hydrosulfide with not less than 25 percent water of crystallization

Substance Data

Source: PubChem (HSDB, 04.12.2019)

CAS-Number

16721-80-5

Flash Point

n/a

Boiling Point

n/a

Emergency Response Guide No. 154

Hazardous Materials Table

Source: 49 CFR §172 (15 June 2026)

(3) Hazard Class

8
Corrosive liquids

(7) Special Provisions (§172.102)

×Note:
Special provisions may be very complex. The extracts are taken from 49 CFR §172.102. Please be careful with the information, as necessary, additional conditions may be applied that are not written here. Please check the original source and report bugs.

Steel packagings must be corrosion-resistant or have protection against corrosion.

Browse special provision A7

IB8

_{Authorized IBCs:} Metal (11A, 11B, 11N, 21A, 21B, 21N, 31A, 31B and 31N); Rigid plastics (11H1, 11H2, 21H1, 21H2, 31H1 and 31H2 ); Composite (11HZ1, 11HZ2, 21HZ1, 21HZ2 and 31HZ1); Fiberboard (11G); Wooden (11C, 11D and 11F); Flexible (13H1, 13H2, 13H3, 13H4, 13H5, 13L1, 13L2, 13L3, 13L4, 13M1 or 13M2).

Browse special provision IB8

IP2

When IBCs other than metal or rigid plastics IBCs are used, they must be offered for transportation in a closed freight container or a closed transport vehicle.

Browse special provision IP2

IP4

Flexible, fiberboard or wooden IBCs must be sift-proof and water-resistant or be fitted with a sift-proof and water-resistant liner.

Browse special provision IP4

Minimum test pressure (bar)	4
Minimum shell thickness	§ 178.274(d)(2)
Pressure-relief requirements	Normal
Bottom opening requirements	§ 178.275(d)(3)

Browse special provision T7

TP2

a. The maximum degree of filling must not exceed the degree of filling determined by the following:
TP2a

Where:
t_r is the maximum mean bulk temperature during transport,
t_f is the temperature in degrees celsius of the liquid during filling, and
α is the mean coefficient of cubical expansion of the liquid between the mean temperature of the liquid during filling (t_f) and the maximum mean bulk temperature during transportation (t_r) both in degrees celsius.
b. For liquids transported under ambient conditions α may be calculated using the formula:
TP2b

Where:
d₁₅ and d₅₀ are the densities (in units of mass per unit volume) of the liquid at 15 °C (59 °F) and 50 °C (122 °F), respectively.

Browse special provision TP2

(8) Packing Authorizations (§173.***)

(8A) Exceptions	154	see 49 CFR §173.154
(8B) Non-bulk	212	see 49 CFR §173.212
(8C) Bulk	240	see 49 CFR §173.240

(9) Quantity Limits

(9A) Passenger aircraft/rail	15 kg
(9B) Cargo aircraft only	50 kg

(10) Vessel stowage

(10A) Location

Stowage category “A” means the material may be stowed “on deck” or “under deck” on a cargo vessel or on a passenger vessel.

Source: 49 CFR §172.101(k)

(10B) Other

52	see 49 CFR §176.84

Source: 49 CFR §176.84

Segregation chart for load, transport, and storage

This chart shows whether loading, transport, or storage with other hazard classes is permitted, prohibited, or restricted. Based on 49 CFR §177.848.

Note: In this segregation and separation chart are HazMat of hazard class 8 considered depending if there are liquid. Currently HazMat Tool is not able to to check if a HazMat is liquid or not. Therefore it is assumed as liquid. See PHMSA Interpretation #09-0252.

Hazard class	8	7	6.1	5.2	5.1	4.3	4.2	4.1	3	2.3B	2.3A	2.2	2.1	1.6	1.5	1.4	1.3	1.1/1.2
1.1/1.2
1.3
1.4
1.5
1.6
2.1
2.2
2.3A
2.3B
3
4.1
4.2
4.3
5.1
5.2
6.1
7
8

	Must not be loaded, transported, or stored together in the same vehicle or facility.
	May be loaded, transported, or stored together.
	May be loaded, transported, or stored together only with restrictions.

Similar substances

UN / ID	Proper shipping name	Hazard class
UN 1382	Potassium sulfide, anhydrous or Potassium sulfide with less than 30 percent water of crystallization	4.2
UN 1385	Sodium sulfide, anhydrous or Sodium sulfide with less than 30 percent water of crystallization	4.2
UN 1847	Potassium sulfide, hydrated with not less than 30 percent water of crystallization	8
UN 2318	Sodium hydrosulfide, with less than 25 percent water of crystallization	4.2