HazMat Tool — substance information

Alkaloids, liquid, n.o.s., or Alkaloid salts, liquid, n.o.s.

HMT May 2026

UN / ID: UN 3140
Hazard class: 6.1
Packing group: I (multiple — see tabs)
ERG guide: ERG 151
Special provisions: SP A4, SP T14, SP TP2, SP TP27
Source: 49 CFR §172 (2026/05)

Spot an error in this entry?

On this page

Alkaloids, liquid, n.o.s., or Alkaloid salts, liquid, n.o.s.

Emergency Response Guide No. 151

Hazardous Materials Table

Source: 49 CFR §172 (2026/05)

Packing group I
Packing group II
Packing group III

(3) Hazard Class

6.1
Poisonous Material

This entry is signed with "G". The letter "G" identifies proper shipping names for which one or more technical names of the hazardous material must be entered in parentheses, in association with the basic description. (See §172.203(k)).

(7) Special Provisions (§172.102)

×Note:
Special provisions may be very complex. The extracts are taken from 49 CFR §172.102. Please be careful with the information, as necessary, additional conditions may be applied that are not written here. Please check the original source and report bugs.

Liquids having an inhalation toxicity of Packing Group I are not permitted on aircraft.

Browse special provision A4

T14

Minimum test pressure (bar)	6
Minimum shell thickness	6 mm
Pressure-relief requirements	§ 178.275(g)(3)
Bottom opening requirements	Prohibited

Browse special provision T14

TP2

a. The maximum degree of filling must not exceed the degree of filling determined by the following:
TP2a

Where:
t_r is the maximum mean bulk temperature during transport,
t_f is the temperature in degrees celsius of the liquid during filling, and
α is the mean coefficient of cubical expansion of the liquid between the mean temperature of the liquid during filling (t_f) and the maximum mean bulk temperature during transportation (t_r) both in degrees celsius.
b. For liquids transported under ambient conditions α may be calculated using the formula:
TP2b

Where:
d₁₅ and d₅₀ are the densities (in units of mass per unit volume) of the liquid at 15 °C (59 °F) and 50 °C (122 °F), respectively.

Browse special provision TP2

TP27

A portable tank having a minimum test pressure of 4 bar (400 kPa) may be used provided the calculated test pressure is 4 bar or less based on the MAWP of the hazardous material, as defined in §178.275, where the test pressure is 1.5 times the MAWP.

Browse special provision TP27

(8) Packing Authorizations (§173.***)

(8A) Exceptions	None
(8B) Non-bulk	201	see 49 CFR §173.201
(8C) Bulk	243	see 49 CFR §173.243

(9) Quantity Limits

(9A) Passenger aircraft/rail	1 L
(9B) Cargo aircraft only	30 L

(10) Vessel stowage

(10A) Location	A Stowage category “A” means the material may be stowed “on deck” or “under deck” on a cargo vessel or on a passenger vessel. Source: 49 CFR §172.101(k)
(10B) Other	n/a

(3) Hazard Class

6.1
Poisonous Material

(4) Identification number

UN 3140

(5) Packing Group

Comparison View of PG

(6) Labels

(1) Symbols

(7) Special Provisions (§172.102)

IB2

Authorized IBCs: Metal (31A, 31B and 31N); Rigid plastics (31H1 and 31H2); Composite (31HZ1).
Additional Requirement: Only liquids with a vapor pressure less than or equal to 110 kPa at 50 °C (1.1 bar at 122 °F), or 130 kPa at 55 °C (1.3 bar at 131 °F) are authorized.

Browse special provision IB2

T11

Minimum test pressure (bar)	6
Minimum shell thickness	§ 178.274(d)(2)
Pressure-relief requirements	Normal
Bottom opening requirements	§ 178.275(d)(3)

Browse special provision T11

TP2

a. The maximum degree of filling must not exceed the degree of filling determined by the following:
TP2a

Where:
d₁₅ and d₅₀ are the densities (in units of mass per unit volume) of the liquid at 15 °C (59 °F) and 50 °C (122 °F), respectively.

Browse special provision TP2

TP27

Browse special provision TP27

(8) Packing Authorizations (§173.***)

(8A) Exceptions	153	see 49 CFR §173.153
(8B) Non-bulk	202	see 49 CFR §173.202
(8C) Bulk	243	see 49 CFR §173.243

(9) Quantity Limits

(9A) Passenger aircraft/rail	5 L
(9B) Cargo aircraft only	60 L

(10) Vessel stowage

(10A) Location	A Stowage category “A” means the material may be stowed “on deck” or “under deck” on a cargo vessel or on a passenger vessel. Source: 49 CFR §172.101(k)
(10B) Other	n/a

(3) Hazard Class

6.1
Poisonous Material

(4) Identification number

UN 3140

(5) Packing Group

III

Comparison View of PG

(6) Labels

(1) Symbols

(7) Special Provisions (§172.102)

IB3

Authorized IBCs: Metal (31A, 31B and 31N); Rigid plastics (31H1 and 31H2); Composite (31HZ1 and 31HA2, 31HB2, 31HN2, 31HD2 and 31HH2).
Additional Requirement: Only liquids with a vapor pressure less than or equal to 110 kPa at 50 °C (1.1 bar at 122 °F), or 130 kPa at 55 °C (1.3 bar at 131 °F) are authorized, except for UN2672 (also see special provision IP8 in Table 2 for UN2672).

Browse special provision IB3

Minimum test pressure (bar)	4
Minimum shell thickness	§ 178.274(d)(2)
Pressure-relief requirements	Normal
Bottom opening requirements	§ 178.275(d)(3)

Browse special provision T7

TP1

The maximum degree of filling must not exceed the degree of filling determined by the following:
TP1

Where:
t_r is the maximum mean bulk temperature during transport, and t_f is the temperature in degrees celsius of the liquid during filling.

Browse special provision TP1

TP28

A portable tank having a minimum test pressure of 2.65 bar (265 kPa) may be used provided the calculated test pressure is 2.65 bar or less based on the MAWP of the hazardous material, as defined in §178.275, where the test pressure is 1.5 times the MAWP.

Browse special provision TP28

(8) Packing Authorizations (§173.***)

(8A) Exceptions	153	see 49 CFR §173.153
(8B) Non-bulk	203	see 49 CFR §173.203
(8C) Bulk	241	see 49 CFR §173.241

(9) Quantity Limits

(9A) Passenger aircraft/rail	60 L
(9B) Cargo aircraft only	220 L

(10) Vessel stowage

(10A) Location	A Stowage category “A” means the material may be stowed “on deck” or “under deck” on a cargo vessel or on a passenger vessel. Source: 49 CFR §172.101(k)
(10B) Other	n/a

Packing group comparison

Multiple packing groups apply to this entry. See assignment criteria in 49 CFR §173 Subpart D. Details are in the tabs above; differences are highlighted.

	PG I	PG II	PG III
1	G	G	G
2	Alkaloids, liquid, n.o.s., or Alkaloid salts, liquid, n.o.s.	Alkaloids, liquid, n.o.s., or Alkaloid salts, liquid, n.o.s.	Alkaloids, liquid, n.o.s., or Alkaloid salts, liquid, n.o.s.
3	6.1	6.1	6.1
4	UN 3140	UN 3140	UN 3140
5	I	II	III
6	6.1	6.1	6.1
7	A4, T14, TP2, TP27	IB2, T11, TP2, TP27	IB3, T7, TP1, TP28
8A	None	153	153
8B	201	202	203
8C	243	243	241
9A	1 L	5 L	60 L
9B	30 L	60 L	220 L
10A	A	A	A
10B	n/a	n/a	n/a

Segregation chart for load, transport, and storage

This chart shows whether loading, transport, or storage with other hazard classes is permitted, prohibited, or restricted. Based on 49 CFR §177.848.

Note: The HMR prohibit only those Division 6.1 liquids that meet the definition of a Packing Group (PG) I and Hazard Zone A. See special provision 1 and PHMSA Interpretation #09-0252.

Packages with POISON or POISON INHALATION HAZARD labels, or a POISON label displaying “PG III,” or “PG III” marked next to a POISON label may not be transported with foodstuffs, feed or any other edible material, intended for humans or animals. For exceptions see 49 CFR §177.841(e).

Scope & sources (important)Click to show CFR references

This check evaluates segregation per 49 CFR §177.848. Additional loading/unloading and handling requirements may still apply; see 49 CFR §177 Subpart B (Loading and Unloading):

§177.834 - General requirements
§177.835 - Class 1 materials
§177.837 - Class 3 materials
§177.838 - Class 4 (flammable solid) materials, Class 5 (oxidizing) materials, and Division 4.2 (pyroforic liquid) materials
§177.839 - Class 8 (corrosive) materials
§177.840 - Class 2 (gases) materials
§177.841 - Division 6.1 and Division 2.3 materials
§177.842 - Class 7 (radioactive) material
§177.843 - Contamination of vehicles

Similar substances

UN / ID	Proper shipping name	Hazard class
UN 1544	Alkaloids, solid, n.o.s. or Alkaloid salts, solid, n.o.s. poisonous	6.1