Chloroacetyl chloride

This material is poisonous by inhalation (see §171.8 of this subchapter) in Hazard Zone B (see §173.116(a) or §173.133(a) of this subchapter), and must be described as an inhalation hazard under the provisions of this subchapter.

Browse special provision 2

MC 300, MC 301, MC 302, MC 303, MC 305, and MC 306 and DOT 406 cargo tanks and DOT 57 portable tanks are not authorized.

Browse special provision B3

Packagings shall be made of nickel, stainless steel, or steel with nickel, stainless steel, lead or other suitable corrosion resistant metallic lining.

Browse special provision B8

Bottom outlets are not authorized.

Browse special provision B9

Each bulk packaging, except a tank car or a multi-unit-tank car tank, must be insulated with an insulating material so that the overall thermal conductance at 15.5 °C (60 °F) is no more than 1.5333 kilojoules per hour per square meter per degree Celsius (0.075 Btu per hour per square foot per degree Fahrenheit) temperature differential. Insulating materials must not promote corrosion to steel when wet.

Browse special provision B14

MC 312, MC 330, MC 331, DOT 412 cargo tanks and DOT 51 portable tanks must be made of stainless steel, except that steel other than stainless steel may be used in accordance with the provisions of §173.24b(b) of this subchapter. Thickness of stainless steel for tank shell and heads for cargo tanks and portable tanks must be the greater of 6.35 mm (0.250 inch) or the thickness required for a tank with a design pressure at least equal to 1.3 times the vapor pressure of the lading at 46 °C (115 °F). In addition, MC 312 and DOT 412 cargo tank motor vehicles must:

• a. Be ASME Code (U) stamped for 100% radiography of all pressure-retaining welds;
• b. Have accident damage protection which conforms with §178.345-8 of this subchapter;
• c. Have a MAWP or design pressure of at least 87 psig; and
• d. Have a bolted manway cover.

Browse special provision B32

Other packaging are authorized when approved by the Associate Administrator.

Browse special provision B77

Aluminum construction materials are not authorized for any part of a packaging which is normally in contact with the hazardous material.

Browse special provision N34

Metal drums are permitted as single packagings only if constructed of nickel or monel.

Browse special provision N43

see 49 CFR §172.102

a. The maximum degree of filling must not exceed the degree of filling determined by the following:

Where:
t_r is the maximum mean bulk temperature during transport,
t_f is the temperature in degrees celsius of the liquid during filling, and α is the mean coefficient of cubical expansion of the liquid between the mean temperature of the liquid during filling (t_f) and the maximum mean bulk temperature during transportation (t_r) both in degrees celsius.
b. For liquids transported under ambient conditions α may be calculated using the formula:
Where:
d₁₅ and d₅₀ are the densities (in units of mass per unit volume) of the liquid at 15 °C (59 °F) and 50 °C (122 °F), respectively.

Browse special provision TP2

Self-contained breathing apparatus must be provided when this hazardous material is transported by sea.

Browse special provision TP13

Each portable tank must be insulated with an insulating material so that the overall thermal conductance at 15.5 °C (60 °F) is no more than 1.5333 kilojoules per hour per square meter per degree Celsius (0.075 Btu per hour per square foot per degree Fahrenheit) temperature differential. Insulating materials may not promote corrosion to steel when wet.

Browse special provision TP38

Each portable tank must be made of stainless steel, except that steel other than stainless steel may be used in accordance with the provisions of 173.24b(b) of this subchapter. Thickness of stainless steel for portable tank shells and heads must be the greater of 6.35 mm (0.250 inch) or the thickness required for a portable tank with a design pressure at least equal to 1.3 times the vapor pressure of the hazardous material at 46 °C (115 °F).

Browse special provision TP45

D

Stowage category “D” means the material must be stowed “on deck only” on a cargo vessel or on a passenger vessel carrying a number of passengers limited to not more than the larger of 25 passengers or one passenger per each 3 m of overall vessel length, but the material is prohibited on a passenger vessel in which the limiting number of passengers is exceeded.

Source: 49 CFR §172.101(k)