HazMat Tool — substance information Reference only — not a shipping paper, placard mandate, or CVI record.

Ethylenediamine

HMT 15 June 2026

UN / ID: UN 1604
Hazard class: 8
Packing group: II (multiple — see tabs)
ERG guide: ERG 132
Special provisions: SP IB2, SP T7, SP TP2
Source: 49 CFR §172 (15 June 2026)

On this page

Ethylenediamine

Ethylenediamine (abbreviated as en when a ligand) is the organic compound with the formula C2H4(NH2)2. This colorless liquid with an ammonia-like odor is a basic amine. It is a widely used building block in chemical synthesis, with approximately 500,000 tonnes produced in 1998. Ethylenediamine is the first member of the so-called polyethylene amines Wikipedia

Substance Data

Source: PubChem

CAS-Number

107-15-3

Flash Point

—

Boiling Point

—

Emergency Response Guide No. 132

Hazardous Materials Table

Source: 49 CFR §172 (15 June 2026)

Packing group II
Packing group III

(3) Hazard class

8
Corrosive liquids

(4) Identification number

UN 1604

(5) Packing Group

Comparison View of PG

(6) Labels

(7) Special Provisions (§172.102)

×Note:
Special provisions may be very complex. The extracts are taken from 49 CFR §172.102. Please be careful with the information, as necessary, additional conditions may be applied that are not written here. Please check the original source and report bugs.

IB2

_{Authorized IBCs:} Metal (31A, 31B and 31N); Rigid plastics (31H1 and 31H2); Composite (31HZ1).
_{Additional Requirement:} Only liquids with a vapor pressure less than or equal to 110 kPa at 50 °C (1.1 bar at 122 °F), or 130 kPa at 55 °C (1.3 bar at 131 °F) are authorized.

Browse special provision IB2

Minimum test pressure (bar)	4
Minimum shell thickness	§ 178.274(d)(2)
Pressure-relief requirements	Normal
Bottom opening requirements	§ 178.275(d)(3)

Browse special provision T7

TP2

a. The maximum degree of filling must not exceed the degree of filling determined by the following:
TP2a

Where:
t_r is the maximum mean bulk temperature during transport,
t_f is the temperature in degrees celsius of the liquid during filling, and
α is the mean coefficient of cubical expansion of the liquid between the mean temperature of the liquid during filling (t_f) and the maximum mean bulk temperature during transportation (t_r) both in degrees celsius.
b. For liquids transported under ambient conditions α may be calculated using the formula:
TP2b

Where:
d₁₅ and d₅₀ are the densities (in units of mass per unit volume) of the liquid at 15 °C (59 °F) and 50 °C (122 °F), respectively.

Browse special provision TP2

(8) Packing Authorizations (§173.***)

(8A) Exceptions	154	see 49 CFR §173.154
(8B) Non-bulk	202	see 49 CFR §173.202
(8C) Bulk	243	see 49 CFR §173.243

(9) Quantity Limits

(9A) Passenger aircraft/rail	1 L
(9B) Cargo aircraft only	30 L

(10) Vessel stowage

(10A) Location

Stowage category “A” means the material may be stowed “on deck” or “under deck” on a cargo vessel or on a passenger vessel.

Source: 49 CFR §172.101(k)

(10B) Other

40	see 49 CFR §176.84
52.	see 49 CFR §176.84

Source: 49 CFR §176.84

(3) Hazard class

8
Corrosive liquids

(4) Identification number

UN 2685

(5) Packing Group

Comparison View of PG

(6) Labels

(7) Special Provisions (§172.102)

IB2

Browse special provision IB2

Minimum test pressure (bar)	4
Minimum shell thickness	§ 178.274(d)(2)
Pressure-relief requirements	Normal
Bottom opening requirements	§ 178.275(d)(3)

Browse special provision T7

TP2

a. The maximum degree of filling must not exceed the degree of filling determined by the following:
TP2a

Where:
d₁₅ and d₅₀ are the densities (in units of mass per unit volume) of the liquid at 15 °C (59 °F) and 50 °C (122 °F), respectively.

Browse special provision TP2

(8) Packing Authorizations (§173.***)

(8A) Exceptions	154	see 49 CFR §173.154
(8B) Non-bulk	202	see 49 CFR §173.202
(8C) Bulk	243	see 49 CFR §173.243

(9) Quantity Limits

(9A) Passenger aircraft/rail	1 L
(9B) Cargo aircraft only	30 L

(10) Vessel stowage

(10A) Location

Stowage category “A” means the material may be stowed “on deck” or “under deck” on a cargo vessel or on a passenger vessel.

Source: 49 CFR §172.101(k)

(10B) Other

52	see 49 CFR §176.84

Source: 49 CFR §176.84

Packing group comparison

Multiple packing groups apply to this entry. See assignment criteria in 49 CFR §173 Subpart D. Details are in the tabs above; differences are highlighted.

	PG II	PG II
1
2	Ethylenediamine	N,N-Diethylethylenediamine
3	8	8
4	UN 1604	UN 2685
5	II	II
6	8, 3	8, 3
7	IB2, T7, TP2	IB2, T7, TP2
8A	154	154
8B	202	202
8C	243	243
9A	1 L	1 L
9B	30 L	30 L
10A	A	A
10B	40, 52.	52

Segregation chart for load, transport, and storage

This chart shows whether loading, transport, or storage with other hazard classes is permitted, prohibited, or restricted. Based on 49 CFR §177.848.

Note: In this segregation and separation chart are HazMat of hazard class 8 considered depending if there are liquid. Currently HazMat Tool is not able to to check if a HazMat is liquid or not. Therefore it is assumed as liquid. See PHMSA Interpretation #09-0252.

Hazard class	8	7	6.1	5.2	5.1	4.3	4.2	4.1	3	2.3B	2.3A	2.2	2.1	1.6	1.5	1.4	1.3	1.1/1.2
1.1/1.2
1.3
1.4
1.5
1.6
2.1
2.2
2.3A
2.3B
3
4.1
4.2
4.3
5.1
5.2
6.1
7
8

	Must not be loaded, transported, or stored together in the same vehicle or facility.
	May be loaded, transported, or stored together.
	May be loaded, transported, or stored together only with restrictions.