HazMat Tool — substance information Reference only — not a shipping paper, placard mandate, or CVI record.

3,5-Dichloro-2,4,6-trifluoropyridine

HMT 15 June 2026

UN / ID: NA 9264
Hazard class: 6.1
Packing group: I (multiple — see tabs)
ERG guide: —
Special provisions: SP 2, SP B9, SP B14, SP B32, SP T20, SP TP4, SP TP13, SP TP38, more…
Source: 49 CFR §172 (15 June 2026)

Spot an error in this entry?

On this page

3,5-Dichloro-2,4,6-trifluoropyridine

Hazardous Materials Table

Source: 49 CFR §172 (15 June 2026)

Packing group I
Packing group II
Packing group III

(3) Hazard class

6.1
Poisonous Material

This entry is signed with "D". The letter "D" identifies proper shipping names which are appropriate for describing materials for domestic transportation but may be inappropriate for international transportation under the provisions of international regulations (e.g., IMO, ICAO). An alternate proper shipping name may be selected when either domestic or international transportation is involved.

(7) Special Provisions (§172.102)

×Note:
Special provisions may be very complex. The extracts are taken from 49 CFR §172.102. Please be careful with the information, as necessary, additional conditions may be applied that are not written here. Please check the original source and report bugs.

This material is poisonous by inhalation (see § 171.8 of this subchapter) in Hazard Zone B (see § 173.116(a) or § 173.133(a) of this subchapter), and must be described as an inhalation hazard under the provisions of this subchapter.

Browse special provision 2

Bottom outlets are not authorized.

Browse special provision B9

B14

Each bulk packaging, except a tank car or a multi-unit-tank car tank, must be insulated with an insulating material so that the overall thermal conductance at 15.5 °C (60 °F) is no more than 1.5333 kilojoules per hour per square meter per degree Celsius (0.075 Btu per hour per square foot per degree Fahrenheit) temperature differential. Insulating materials must not promote corrosion to steel when wet.

Browse special provision B14

B32

MC 312, MC 330, MC 331, DOT 412 cargo tanks and DOT 51 portable tanks must be made of stainless steel, except that steel other than stainless steel may be used in accordance with the provisions of § 173.24b(b) of this subchapter. Thickness of stainless steel for tank shell and heads for cargo tanks and portable tanks must be the greater of 6.35 mm (0.250 inch) or the thickness required for a tank with a design pressure at least equal to 1.3 times the vapor pressure of the lading at 46 °C (115 °F). In addition, MC 312 and DOT 412 cargo tank motor vehicles must:
a. Be ASME Code (U) stamped for 100% radiography of all pressure-retaining welds;
b. Have accident damage protection which conforms with § 178.345-8 of this subchapter;
c. Have a MAWP or design pressure of at least 87 psig; and
d. Have a bolted manway cover.

Browse special provision B32

T20

Minimum test pressure (bar)	10
Minimum shell thickness	8 mm
Pressure-relief requirements	§ 178.275(g)(3)
Bottom opening requirements	Prohibited

Browse special provision T20

TP4

The maximum degree of filling for portable tanks must not exceed 90%.

Browse special provision TP4

TP13

Self-contained breathing apparatus must be provided when this hazardous material is transported by sea.

Browse special provision TP13

TP38

Each portable tank must be insulated with an insulating material so that the overall thermal conductance at 15.5 °C (60 °F) is no more than 1.5333 kilojoules per hour per square meter per degree Celsius (0.075 Btu per hour per square foot per degree Fahrenheit) temperature differential. Insulating materials may not promote corrosion to steel when wet.

Browse special provision TP38

TP45

Each portable tank must be made of stainless steel, except that steel other than stainless steel may be used in accordance with the provisions of 173.24b(b) of this subchapter. Thickness of stainless steel for portable tank shells and heads must be the greater of 6.35 mm (0.250 inch) or the thickness required for a portable tank with a design pressure at least equal to 1.3 times the vapor pressure of the hazardous material at 46 °C (115 °F).

Browse special provision TP45

(8) Packing Authorizations (§173.***)

(8A) Exceptions	None
(8B) Non-bulk	227	see 49 CFR §173.227
(8C) Bulk	244	see 49 CFR §173.244

(9) Quantity Limits

(9A) Passenger aircraft/rail	Forbidden
(9B) Cargo aircraft only	Forbidden

(10) Vessel stowage

(10A) Location

Stowage category “A” means the material may be stowed “on deck” or “under deck” on a cargo vessel or on a passenger vessel.

Source: 49 CFR §172.101(k)

(10B) Other

40	see 49 CFR §176.84

Source: 49 CFR §176.84

(3) Hazard class

3
Flammable liquids

(4) Identification number

UN 2410

(5) Packing Group

Comparison View of PG

(6) Labels

(7) Special Provisions (§172.102)

IB2

_{Authorized IBCs:} Metal (31A, 31B and 31N); Rigid plastics (31H1 and 31H2); Composite (31HZ1).
_{Additional Requirement:} Only liquids with a vapor pressure less than or equal to 110 kPa at 50 °C (1.1 bar at 122 °F), or 130 kPa at 55 °C (1.3 bar at 131 °F) are authorized.

Browse special provision IB2

Minimum test pressure (bar)	2.65
Minimum shell thickness	§ 178.274(d)(2)
Pressure-relief requirements	Normal
Bottom opening requirements	§ 178.275(d)(3)

Browse special provision T4

TP1

The maximum degree of filling must not exceed the degree of filling determined by the following:
TP1

Where:
t_r is the maximum mean bulk temperature during transport, and t_f is the temperature in degrees celsius of the liquid during filling.

Browse special provision TP1

(8) Packing Authorizations (§173.***)

(8A) Exceptions	150	see 49 CFR §173.150
(8B) Non-bulk	202	see 49 CFR §173.202
(8C) Bulk	242	see 49 CFR §173.242

(9) Quantity Limits

(9A) Passenger aircraft/rail	5 L
(9B) Cargo aircraft only	60 L

(10) Vessel stowage

(10A) Location	B Stowage category “B” means (i) The material may be stowed “on deck” or “under deck” on a cargo vessel and on a passenger vessel carrying a number of passengers limited to not more than the larger of 25 passengers, or one passenger per each 3 m of overall vessel length; and (ii) “On deck only” on passenger vessels in which the number of passengers specified in paragraph (k)(2)(i) of this section is exceeded. Source: 49 CFR §172.101(k)
(10B) Other	—

(3) Hazard class

6.1
Poisonous Material

(4) Identification number

UN 2822

(5) Packing Group

Comparison View of PG

(6) Labels

(7) Special Provisions (§172.102)

IB2

Browse special provision IB2

Minimum test pressure (bar)	4
Minimum shell thickness	§ 178.274(d)(2)
Pressure-relief requirements	Normal
Bottom opening requirements	§ 178.275(d)(3)

Browse special provision T7

TP2

a. The maximum degree of filling must not exceed the degree of filling determined by the following:
TP2a

Where:
t_r is the maximum mean bulk temperature during transport,
t_f is the temperature in degrees celsius of the liquid during filling, and
α is the mean coefficient of cubical expansion of the liquid between the mean temperature of the liquid during filling (t_f) and the maximum mean bulk temperature during transportation (t_r) both in degrees celsius.
b. For liquids transported under ambient conditions α may be calculated using the formula:
TP2b

Where:
d₁₅ and d₅₀ are the densities (in units of mass per unit volume) of the liquid at 15 °C (59 °F) and 50 °C (122 °F), respectively.

Browse special provision TP2

(8) Packing Authorizations (§173.***)

(8A) Exceptions	153	see 49 CFR §173.153
(8B) Non-bulk	202	see 49 CFR §173.202
(8C) Bulk	243	see 49 CFR §173.243

(9) Quantity Limits

(9A) Passenger aircraft/rail	5 L
(9B) Cargo aircraft only	60 L

(10) Vessel stowage

(10A) Location

Stowage category “A” means the material may be stowed “on deck” or “under deck” on a cargo vessel or on a passenger vessel.

Source: 49 CFR §172.101(k)

(10B) Other

40	see 49 CFR §176.84

Source: 49 CFR §176.84

(3) Hazard class

3
Flammable liquids

(4) Identification number

UN 1282

(5) Packing Group

Comparison View of PG

(6) Labels

(7) Special Provisions (§172.102)

IB2

Browse special provision IB2

Minimum test pressure (bar)	2.65
Minimum shell thickness	§ 178.274(d)(2)
Pressure-relief requirements	Normal
Bottom opening requirements	§ 178.275(d)(3)

Browse special provision T4

TP2

a. The maximum degree of filling must not exceed the degree of filling determined by the following:
TP2a

Where:
d₁₅ and d₅₀ are the densities (in units of mass per unit volume) of the liquid at 15 °C (59 °F) and 50 °C (122 °F), respectively.

Browse special provision TP2

(8) Packing Authorizations (§173.***)

(8A) Exceptions	150	see 49 CFR §173.150
(8B) Non-bulk	202	see 49 CFR §173.202
(8C) Bulk	242	see 49 CFR §173.242

(9) Quantity Limits

(9A) Passenger aircraft/rail	5 L
(9B) Cargo aircraft only	60 L

(10) Vessel stowage

(10A) Location

Stowage category “B” means

(i) The material may be stowed “on deck” or “under deck” on a cargo vessel and on a passenger vessel carrying a number of passengers limited to not more than the larger of 25 passengers, or one passenger per each 3 m of overall vessel length; and
(ii) “On deck only” on passenger vessels in which the number of passengers specified in paragraph (k)(2)(i) of this section is exceeded.

Source: 49 CFR §172.101(k)

(10B) Other

21	see 49 CFR §176.84
100	see 49 CFR §176.84

Source: 49 CFR §176.84

(3) Hazard class

6.1
Poisonous Material

(4) Identification number

UN 2300

(5) Packing Group

III

Comparison View of PG

(6) Labels

(7) Special Provisions (§172.102)

IB3

_{Authorized IBCs:} Metal (31A, 31B and 31N); Rigid plastics (31H1 and 31H2); Composite (31HZ1 and 31HA2, 31HB2, 31HN2, 31HD2 and 31HH2).
_{Additional Requirement:} Only liquids with a vapor pressure less than or equal to 110 kPa at 50 °C (1.1 bar at 122 °F), or 130 kPa at 55 °C (1.3 bar at 131 °F) are authorized, except for UN2672 (also see special provision IP8 in Table 2 for UN2672).

Browse special provision IB3

Minimum test pressure (bar)	2.65
Minimum shell thickness	§ 178.274(d)(2)
Pressure-relief requirements	Normal
Bottom opening requirements	§ 178.275(d)(3)

Browse special provision T4

TP1

The maximum degree of filling must not exceed the degree of filling determined by the following:
TP1

Where:
t_r is the maximum mean bulk temperature during transport, and t_f is the temperature in degrees celsius of the liquid during filling.

Browse special provision TP1

(8) Packing Authorizations (§173.***)

(8A) Exceptions	153	see 49 CFR §173.153
(8B) Non-bulk	203	see 49 CFR §173.203
(8C) Bulk	241	see 49 CFR §173.241

(9) Quantity Limits

(9A) Passenger aircraft/rail	60 L
(9B) Cargo aircraft only	220 L

(10) Vessel stowage

(10A) Location	A Stowage category “A” means the material may be stowed “on deck” or “under deck” on a cargo vessel or on a passenger vessel. Source: 49 CFR §172.101(k)
(10B) Other	—

Packing group comparison

Multiple packing groups apply to this entry. See assignment criteria in 49 CFR §173 Subpart D. Details are in the tabs above; differences are highlighted.

	PG I	PG II	PG II	PG II	PG III
1	D
2	3,5-Dichloro-2,4,6-trifluoropyridine	1,2,3,6-Tetrahydropyridine	2-Chloropyridine	Pyridine	2-Methyl-5-ethylpyridine
3	6.1	3	6.1	3	6.1
4	NA 9264	UN 2410	UN 2822	UN 1282	UN 2300
5	I	II	II	II	III
6	6.1	3	6.1	3	6.1
7	2, B9, B14, B32, T20, TP4, TP13, TP38, TP45	IB2, T4, TP1	IB2, T7, TP2	IB2, T4, TP2	IB3, T4, TP1
8A	None	150	153	150	153
8B	227	202	202	202	203
8C	244	242	243	242	241
9A	Forbidden	5 L	5 L	5 L	60 L
9B	Forbidden	60 L	60 L	60 L	220 L
10A	A	B	A	B	A
10B	40	—	40	21, 100	—

Segregation chart for load, transport, and storage

This chart shows whether loading, transport, or storage with other hazard classes is permitted, prohibited, or restricted. Based on 49 CFR §177.848.

Note: The HMR prohibit only those Division 6.1 liquids that meet the definition of a Packing Group (PG) I and Hazard Zone A. See special provision 1 and PHMSA Interpretation #09-0252.

Packages with POISON or POISON INHALATION HAZARD labels, or a POISON label displaying “PG III,” or “PG III” marked next to a POISON label may not be transported with foodstuffs, feed or any other edible material, intended for humans or animals. For exceptions see 49 CFR §177.841(e).

Scope & sources (important)Click to show CFR references

This check evaluates segregation per 49 CFR §177.848. Additional loading/unloading and handling requirements may still apply; see 49 CFR §177 Subpart B (Loading and Unloading):

§177.834 - General requirements
§177.835 - Class 1 materials
§177.837 - Class 3 materials
§177.838 - Class 4 (flammable solid) materials, Class 5 (oxidizing) materials, and Division 4.2 (pyroforic liquid) materials
§177.839 - Class 8 (corrosive) materials
§177.840 - Class 2 (gases) materials
§177.841 - Division 6.1 and Division 2.3 materials
§177.842 - Class 7 (radioactive) material
§177.843 - Contamination of vehicles