HazMat Tool — substance information Reference only — not a shipping paper, placard mandate, or CVI record.

Dichlorophenyl isocyanates

HMT 15 June 2026

UN / ID: UN 2250
Hazard class: 6.1
Packing group: II
ERG guide: ERG 156
Special provisions: SP IB8, SP IP2, SP IP4, SP T3, SP TP33
Source: 49 CFR §172 (15 June 2026)

On this page

Dichlorophenyl isocyanates

3,4-Dichlorophenyl isocyanate is a chemical compound used as a chemical intermediate and in organic synthesis. It is a solid, and ranges in colour from white to yellow. It is an irritant for tissues including eyes and mucous membranes, and inhalation of dust from the chemical is poisonous. It can be used industrially in the preparation of triclocarban by reaction with p-chloroaniline Wikipedia

Substance Data

Source: PubChem (HSDB, 30.11.2019)

CAS-Number

102-36-3

Flash Point

—

Boiling Point

—

Emergency Response Guide No. 156

Hazardous Materials Table

Source: 49 CFR §172 (15 June 2026)

(3) Hazard class

6.1
Poisonous Material

(4) Identification number

UN 2250

(5) Packing Group

(6) Labels

(7) Special Provisions (§172.102)

×Note:
Special provisions may be very complex. The extracts are taken from 49 CFR §172.102. Please be careful with the information, as necessary, additional conditions may be applied that are not written here. Please check the original source and report bugs.

IB8

_{Authorized IBCs:} Metal (11A, 11B, 11N, 21A, 21B, 21N, 31A, 31B and 31N); Rigid plastics (11H1, 11H2, 21H1, 21H2, 31H1 and 31H2 ); Composite (11HZ1, 11HZ2, 21HZ1, 21HZ2 and 31HZ1); Fiberboard (11G); Wooden (11C, 11D and 11F); Flexible (13H1, 13H2, 13H3, 13H4, 13H5, 13L1, 13L2, 13L3, 13L4, 13M1 or 13M2).

Browse special provision IB8

IP2

When IBCs other than metal or rigid plastics IBCs are used, they must be offered for transportation in a closed freight container or a closed transport vehicle.

Browse special provision IP2

IP4

Flexible, fiberboard or wooden IBCs must be sift-proof and water-resistant or be fitted with a sift-proof and water-resistant liner.

Browse special provision IP4

Minimum test pressure (bar)	2.65
Minimum shell thickness	§ 178.274(d)(2)
Pressure-relief requirements	Normal
Bottom opening requirements	§ 178.275(d)(2)

Browse special provision T3

TP33

The portable tank instruction assigned for this substance applies for granular and powdered solids and for solids which are filled and discharged at temperatures above their melting point which are cooled and transported as a solid mass. Solid substances transported or offered for transport above their melting point are authorized for transportation in portable tanks conforming to the provisions of portable tank instruction T4 for solid substances of packing group III or T7 for solid substances of packing group II, unless a tank with more stringent requirements for minimum shell thickness, maximum allowable working pressure, pressure-relief devices or bottom outlets are assigned in which case the more stringent tank instruction and special provisions shall apply. Filling limits must be in accordance with portable tank special provision TP3. Solids meeting the definition of an elevated temperature material must be transported in accordance with the applicable requirements of this subchapter.

Browse special provision TP33

(8) Packing Authorizations (§173.***)

(8A) Exceptions	153	see 49 CFR §173.153
(8B) Non-bulk	212	see 49 CFR §173.212
(8C) Bulk	242	see 49 CFR §173.242

(9) Quantity Limits

(9A) Passenger aircraft/rail	25 kg
(9B) Cargo aircraft only	100 kg

(10) Vessel stowage

(10A) Location

Stowage category “B” means

(i) The material may be stowed “on deck” or “under deck” on a cargo vessel and on a passenger vessel carrying a number of passengers limited to not more than the larger of 25 passengers, or one passenger per each 3 m of overall vessel length; and
(ii) “On deck only” on passenger vessels in which the number of passengers specified in paragraph (k)(2)(i) of this section is exceeded.

Source: 49 CFR §172.101(k)

(10B) Other

25	see 49 CFR §176.84
40	see 49 CFR §176.84

Source: 49 CFR §176.84

Segregation chart for load, transport, and storage

This chart shows whether loading, transport, or storage with other hazard classes is permitted, prohibited, or restricted. Based on 49 CFR §177.848.

Note: The HMR prohibit only those Division 6.1 liquids that meet the definition of a Packing Group (PG) I and Hazard Zone A. See special provision 1 and PHMSA Interpretation #09-0252.

Packages with POISON or POISON INHALATION HAZARD labels, or a POISON label displaying “PG III,” or “PG III” marked next to a POISON label may not be transported with foodstuffs, feed or any other edible material, intended for humans or animals. For exceptions see 49 CFR §177.841(e).

Scope & sources (important)Click to show CFR references

This check evaluates segregation per 49 CFR §177.848. Additional loading/unloading and handling requirements may still apply; see 49 CFR §177 Subpart B (Loading and Unloading):

§177.834 - General requirements
§177.835 - Class 1 materials
§177.837 - Class 3 materials
§177.838 - Class 4 (flammable solid) materials, Class 5 (oxidizing) materials, and Division 4.2 (pyroforic liquid) materials
§177.839 - Class 8 (corrosive) materials
§177.840 - Class 2 (gases) materials
§177.841 - Division 6.1 and Division 2.3 materials
§177.842 - Class 7 (radioactive) material
§177.843 - Contamination of vehicles

Similar substances

UN / ID	Proper shipping name	Hazard class
UN 2904	Chlorophenolates, liquid or Phenolates, liquid	8
UN 2905	Chlorophenolates, solid or Phenolates, solid	8
UN 1753	Chlorophenyltrichlorosilane	8
UN 1766	Dichlorophenyltrichlorosilane	8