HazMat Tool — substance information Reference only — not a shipping paper, placard mandate, or CVI record.

Titanium disulphide

HMT 15 June 2026

UN / ID: UN 3174
Hazard class: 4.2
Packing group: III
ERG guide: ERG 135
Special provisions: SP IB8, SP IP3, SP T1, SP TP33, SP W31
Source: 49 CFR §172 (15 June 2026)

On this page

Titanium disulphide

Titanium disulfide is an inorganic compound with the formula TiS2. A golden yellow solid with high electrical conductivity, it belongs to a group of compounds called transition metal dichalcogenides, which consist of the stoichiometry ME2. TiS2 has been employed as a cathode material in rechargeable batteries Wikipedia

Emergency Response Guide No. 135

Hazardous Materials Table

Source: 49 CFR §172 (15 June 2026)

(3) Hazard class

4.2
Spontaneously combustible materials

(4) Identification number

UN 3174

(5) Packing Group

III

(6) Labels

Spontaneously combustible materials (4.2)

(7) Special Provisions (§172.102)

×Note:
Special provisions may be very complex. The extracts are taken from 49 CFR §172.102. Please be careful with the information, as necessary, additional conditions may be applied that are not written here. Please check the original source and report bugs.

IB8

_{Authorized IBCs:} Metal (11A, 11B, 11N, 21A, 21B, 21N, 31A, 31B and 31N); Rigid plastics (11H1, 11H2, 21H1, 21H2, 31H1 and 31H2 ); Composite (11HZ1, 11HZ2, 21HZ1, 21HZ2 and 31HZ1); Fiberboard (11G); Wooden (11C, 11D and 11F); Flexible (13H1, 13H2, 13H3, 13H4, 13H5, 13L1, 13L2, 13L3, 13L4, 13M1 or 13M2).

Browse special provision IB8

IP3

Flexible IBCs must be sift-proof and water-resistant or must be fitted with a sift-proof and water-resistant liner.

Browse special provision IP3

Minimum test pressure (bar)	1.5
Minimum shell thickness	§ 178.274(d)(2)
Pressure-relief requirements	Normal
Bottom opening requirements	§ 178.275(d)(2)

Browse special provision T1

TP33

The portable tank instruction assigned for this substance applies for granular and powdered solids and for solids which are filled and discharged at temperatures above their melting point which are cooled and transported as a solid mass. Solid substances transported or offered for transport above their melting point are authorized for transportation in portable tanks conforming to the provisions of portable tank instruction T4 for solid substances of packing group III or T7 for solid substances of packing group II, unless a tank with more stringent requirements for minimum shell thickness, maximum allowable working pressure, pressure-relief devices or bottom outlets are assigned in which case the more stringent tank instruction and special provisions shall apply. Filling limits must be in accordance with portable tank special provision TP3. Solids meeting the definition of an elevated temperature material must be transported in accordance with the applicable requirements of this subchapter.

Browse special provision TP33

W31

Non-bulk packagings must be hermetically sealed.

Browse special provision W31

(8) Packing Authorizations (§173.***)

(8A) Exceptions	None
(8B) Non-bulk	213	see 49 CFR §173.213
(8C) Bulk	241	see 49 CFR §173.241

(9) Quantity Limits

(9A) Passenger aircraft/rail	25 kg
(9B) Cargo aircraft only	100 kg

(10) Vessel stowage

(10A) Location	A Stowage category “A” means the material may be stowed “on deck” or “under deck” on a cargo vessel or on a passenger vessel. Source: 49 CFR §172.101(k)
(10B) Other	—

Segregation chart for load, transport, and storage

This chart shows whether loading, transport, or storage with other hazard classes is permitted, prohibited, or restricted. Based on 49 CFR §177.848.

Hazard class	8	7	6.1	5.2	5.1	4.3	4.2	4.1	3	2.3B	2.3A	2.2	2.1	1.6	1.5	1.4	1.3	1.1/1.2
1.1/1.2
1.3
1.4
1.5
1.6
2.1
2.2
2.3A
2.3B
3
4.1
4.2
4.3
5.1
5.2
6.1
7
8

	Must not be loaded, transported, or stored together in the same vehicle or facility.
	May be loaded, transported, or stored together.
	May be loaded, transported, or stored together only with restrictions.

Similar substances

UN / ID	Proper shipping name	Hazard class
UN 1352	Titanium powder, wetted with not less than 25 percent water (a visible excess of water must be present) (a) mechanically produced, particle size less than 53 microns; (b) chemically produced, particle size less than 840 microns	4.1
UN 2441	Titanium trichloride, pyrophoric or Titanium trichloride mixtures, pyrophoric	4.2
UN 2878	Titanium sponge granules or Titanium sponge powders	4.1
UN 2546	Titanium powder, dry	4.2
UN 2869	Titanium trichloride mixtures	8
UN 1871	Titanium hydride	4.1
UN 1838	Titanium tetrachloride	6.1