MSDS to GHS Compliance

EHS Professionals, with Global expertise, Providing SDS Authoring and GHS Compliance Services.

SDS Authoring • Expedited (24hr Service) •
MSDS to SDS conversion • GHS Labels • Translation • Compliance review

Potassium fluoride, solid

Potassium fluoride is the chemical compound with the formula KF. After hydrogen fluoride, KF is the primary source of the fluoride ion for applications in manufacturing and in chemistry. It is an alkali halide and occurs naturally as the rare mineral carobbiite. Solutions of KF will etch glass due to the formation of soluble fluorosilicates, although HF is more effective. Wikipedia

Emergency Response Guide No. 154

Data from the Hazardous Materials Table

Source: 49 CFR §172 (2018/07)

(3) Hazard Class

6.1
Poisonous Material

(4) Identification number

UN 1812

(5) Packing Group

III

(6) Labels

(7) Special Provisions (§172.102)

×Note:
Special provisions may be very complex. The extracts are taken from 49 CFR §172.102. Please be careful with the information, as necessary, additional conditions may be applied that are not written here. Please check the original source and report bugs.

IB8	Authorized IBCs: Metal (11A, 11B, 11N, 21A, 21B, 21N, 31A, 31B and 31N); Rigid plastics (11H1, 11H2, 21H1, 21H2, 31H1 and 31H2 ); Composite (11HZ1, 11HZ2, 21HZ1, 21HZ2 and 31HZ1); Fiberboard (11G); Wooden (11C, 11D and 11F); Flexible (13H1, 13H2, 13H3, 13H4, 13H5, 13L1, 13L2, 13L3, 13L4, 13M1 or 13M2). Browse special provision IB8
IP3	Flexible IBCs must be sift-proof and water- resistant or must be fitted with a sift- proof and water-resistant liner. Browse special provision IP3
T1	see 49 CFR §172.102
TP33	The portable tank instruction assigned for this substance applies for granular and powdered solids and for solids which are filled and discharged at temperatures above their melting point which are cooled and transported as a solid mass. Solid substances transported or offered for transport above their melting point are authorized for transportation in portable tanks conforming to the provisions of portable tank instruction T4 for solid substances of packing group III or T7 for solid substances of packing group II, unless a tank with more stringent requirements for minimum shell thickness, maximum allowable working pressure, pressure-relief devices or bottom outlets are assigned in which case the more stringent tank instruction and special provisions shall apply. Filling limits must be in accordance with portable tank special provision TP3. Solids meeting the definition of an elevated temperature material must be transported in accordance with the applicable requirements of this subchapter. Browse special provision TP33

(8) Packing Authorizations (§173.***)

(8A) Exceptions	153	see 49 CFR §173.153
(8B) Non-bulk	213	see 49 CFR §173.213
(8C) Bulk	240	see 49 CFR §173.240

(9) Quantity Limits

(9A) Passenger aircraft/rail	100 kg
(9B) Cargo aircraft only	200 kg

(10) Vessel stowage

(10A) Location

Stowage category “A” means the material may be stowed “on deck” or “under deck” on a cargo vessel or on a passenger vessel.

Source: 49 CFR §172.101(k)

(10B) Other

52	Stow “separated from” acids.¹ ²

¹For waste cyanides or waste cyanide mixtures or solutions, refer to §173.12(e) of this subchapter.

² Class 8 materials in PG II or III that otherwise are required to be segregated from one another may be transported in the same cargo transport unit, whether in the same packaging or not, provided the substances do not react dangerously with each other to cause combustion and/or evolution of considerable heat, or of flammable, toxic or asphyxiant gases, or the formation of corrosive or unstable substances; and the package does not contain more than 30 L (7.8 gallons) for liquids or 30 kg (66 lbs.) for solids.

Source: 49 CFR §176.84

Segregation Chart for Load, Transport, Storage

In this table a statement is contained for each hazard class whether the loading, transport or storage with other hazard classes is allowed, is not permitted or is restricted. The table is based on U.S.-Code 49 CFR §177.848.

Note: The HMR prohibit only those Division 6.1 liquids that meet the definition of a Packing Group (PG) I and Hazard Zone A. See special provision 1 and PHMSA Interpretation #09-0252.

Packages with POISON or POISON INHALATION HAZARD labels, or a POISON label displaying “PG III,” or “PG III” marked next to a POISON label may not be transported with foodstuffs, feed or any other edible material, intended for humans or animals. For exceptions see 49 CFR §177.841(e).

There are no restrictions with hazardous materials, as pointed out in the instructions for using the Segregation Table (see 49 CFR §177.848(e)). But please, refer to following requirements in 49 CFR §177 Subpart B (Loading and Unloading):

§177.834 - General requirements
§177.835 - Class 1 materials
§177.837 - Class 3 materials
§177.838 - Class 4 (flammable solid) materials, Class 5 (oxidizing) materials, and Division 4.2 (pyroforic liquid) materials.
§177.839 - Class 8 (corrosive) materials
§177.840 - Class 2 (gases) materials
§177.841 - Division 6.1 and Division 2.3 materials
§177.842 - Class 7 (radioactive) material
§177.843 - Contamination of vehicles.

Substances with similar name

UN-Number	Name	Hazard Class
	Chlorate of potash, see Potassium chlorate
UN 1626	Mercuric potassium cyanide	6.1
UN 1643	Mercury potassium iodide	6.1
UN 2257	Potassium	4.3
UN 1677	Potassium arsenate	6.1
	Potassium bisulfite solution, see Bisulfites, aqueous solutions, n.o.s.
UN 1870	Potassium borohydride	4.3
UN 1484	Potassium bromate	5.1
UN 2427	Potassium chlorate, aqueous solution	5.1
UN 1679	Potassium cuprocyanide	6.1
UN 1929	Potassium dithionite or Potassium hydrosulfite	4.2
UN 1812	Potassium fluoride, solid	6.1
UN 3422	Potassium fluoride solution	6.1
UN 2628	Potassium fluoroacetate	6.1
UN 1811	Potassium hydrogendifluoride solid	8
UN 3421	Potassium hydrogendifluoride solution	8
	Potassium hydrosulfite, see Potassium dithionite
UN 1814	Potassium hydroxide, solution	8
UN 1487	Potassium nitrate and sodium nitrite mixtures	5.1
UN 1492	Potassium persulfate	5.1
UN 2012	Potassium phosphide	4.3
UN 1422	Potassium sodium alloys, liquid	4.3
UN 3404	Potassium sodium alloys, solid	4.3
UN 1382	Potassium sulfide, anhydrous or Potassium sulfide with less than 30 percent water of crystallization	4.2
UN 1847	Potassium sulfide, hydrated with not less than 30 percent water of crystallization	8