Sodium sulfide, anhydrous or Sodium sulfide with less than 30 percent water of crystallization

Sodium sulfide is a chemical compound with the formula Na2S. More common is its hydrate Na2S·9H2O. Both the anhydrous and the hydrated salts are colorless solids, although technical grades of sodium sulfide are generally yellow to brick red owing to the presence of polysulfides. It is commonly supplied as a crystalline mass, in flake form, or as a fused solid. Wikipedia

Substance Data

Source: TOXNET

CAS-Number

1313-82-2

Flash Point

n/a

Boiling Point

n/a

Emergency Response Guide No. 135

Data from the Hazardous Materials Table

Source: 49 CFR §172 (2018/07)

(3) Hazard Class

4.2
Spontaneously combustible materials

(4) Identification number

UN 1385

(5) Packing Group

(6) Labels

Spontaneously combustible materials (4.2)

(7) Special Provisions (§172.102)

×Note:
Special provisions may be very complex. The extracts are taken from 49 CFR §172.102. Please be careful with the information, as necessary, additional conditions may be applied that are not written here. Please check the original source and report bugs.

A19	Combination packagings consisting of outer fiber drums or plywood drums, with inner plastic packagings, are not authorized for transportation by aircraft. Browse special provision A19
A20	Plastic bags as inner receptacles of combination packagings are not authorized for transportation by aircraft. Browse special provision A20
IB6	Authorized IBCs: Metal (11A, 11B, 11N, 21A, 21B, 21N, 31A, 31B and 31N); Rigid plastics (11H1, 11H2, 21H1, 21H2, 31H1 and 31H2); Composite (11HZ1, 11HZ2, 21HZ1, 21HZ2 and 31HZ1). Additional Requirement: Composite IBCs 11HZ2 and 21HZ2 may not be used when the hazardous materials being transported may become liquid during transport. Browse special provision IB6
IP2	When IBCs other than metal or rigid plastics IBCs are used, they must be offered for transportation in a closed freight container or a closed transport vehicle. Browse special provision IP2
N34	Aluminum construction materials are not authorized for any part of a packaging which is normally in contact with the hazardous material. Browse special provision N34
T3	see 49 CFR §172.102
TP33	The portable tank instruction assigned for this substance applies for granular and powdered solids and for solids which are filled and discharged at temperatures above their melting point which are cooled and transported as a solid mass. Solid substances transported or offered for transport above their melting point are authorized for transportation in portable tanks conforming to the provisions of portable tank instruction T4 for solid substances of packing group III or T7 for solid substances of packing group II, unless a tank with more stringent requirements for minimum shell thickness, maximum allowable working pressure, pressure-relief devices or bottom outlets are assigned in which case the more stringent tank instruction and special provisions shall apply. Filling limits must be in accordance with portable tank special provision TP3. Solids meeting the definition of an elevated temperature material must be transported in accordance with the applicable requirements of this subchapter. Browse special provision TP33
W31	see 49 CFR §172.102
W40	see 49 CFR §172.102

(8) Packing Authorizations (§173.***)

(8A) Exceptions	None
(8B) Non-bulk	212	see 49 CFR §173.212
(8C) Bulk	241	see 49 CFR §173.241

(9) Quantity Limits

(9A) Passenger aircraft/rail	15 kg
(9B) Cargo aircraft only	50 kg

(10) Vessel stowage

(10A) Location

Stowage category “A” means the material may be stowed “on deck” or “under deck” on a cargo vessel or on a passenger vessel.

Source: 49 CFR §172.101(k)

(10B) Other

52	Stow “separated from” acids.¹ ²

¹For waste cyanides or waste cyanide mixtures or solutions, refer to §173.12(e) of this subchapter.

² Class 8 materials in PG II or III that otherwise are required to be segregated from one another may be transported in the same cargo transport unit, whether in the same packaging or not, provided the substances do not react dangerously with each other to cause combustion and/or evolution of considerable heat, or of flammable, toxic or asphyxiant gases, or the formation of corrosive or unstable substances; and the package does not contain more than 30 L (7.8 gallons) for liquids or 30 kg (66 lbs.) for solids.

Source: 49 CFR §176.84

Segregation Chart for Load, Transport, Storage

In this table a statement is contained for each hazard class whether the loading, transport or storage with other hazard classes is allowed, is not permitted or is restricted. The table is based on U.S.-Code 49 CFR §177.848.

Hazard Class	8	7	6.1	5.2	5.1	4.3	4.2	4.1	3	2.3B	2.3A	2.2	2.1	1.6	1.5	1.4	1.3	1.1/1.2
1.1/1.2
1.3
1.4
1.5
1.6
2.1
2.2
2.3A
2.3B
3
4.1
4.2
4.3
5.1
5.2
6.1
7
8

	May not be loaded, transported, or stored together in the same transport vehicle or storage facility.
	Load, transport, storage together is not restricted.
	Load, transport, storage together is allowed under restrictions.

Substances with similar name

UN-Number	Name	Hazard Class
UN 1847	Potassium sulfide, hydrated with not less than 30 percent water of crystallization	8
UN 2318	Sodium hydrosulfide, with less than 25 percent water of crystallization	4.2
UN 2949	Sodium hydrosulfide with not less than 25 percent water of crystallization	8
UN 1385	Sodium sulfide, anhydrous or Sodium sulfide with less than 30 percent water of crystallization	4.2