HazMat Tool — substance information

Aluminum bromide, anhydrous

HMT 15 June 2026

UN / ID: UN 1725
Hazard class: 8
Packing group: II
ERG guide: ERG 137
Special provisions: SP IB8, SP IP2, SP IP4, SP T3, SP TP33
Source: 49 CFR §172 (15 June 2026)

On this page

Aluminum bromide, anhydrous

Aluminium bromide is any chemical compound with the empirical formula AlBrx. Aluminium tribromide is the most common form of aluminium bromide. It is a colorless, sublimable hygroscopic solid; hence old samples tend to be hydrated, mostly as aluminium tribromide hexahydrate (AlBr3·6H2O) Wikipedia

Substance Data

Source: PubChem (HSDB, 15.12.2019)

CAS-Number

7727-15-3

Flash Point

n/a

Boiling Point

n/a

Emergency Response Guide No. 137

Hazardous Materials Table

Source: 49 CFR §172 (15 June 2026)

(3) Hazard Class

8
Corrosive liquids

(4) Identification number

UN 1725

(5) Packing Group

(6) Labels

(7) Special Provisions (§172.102)

×Note:
Special provisions may be very complex. The extracts are taken from 49 CFR §172.102. Please be careful with the information, as necessary, additional conditions may be applied that are not written here. Please check the original source and report bugs.

IB8

_{Authorized IBCs:} Metal (11A, 11B, 11N, 21A, 21B, 21N, 31A, 31B and 31N); Rigid plastics (11H1, 11H2, 21H1, 21H2, 31H1 and 31H2 ); Composite (11HZ1, 11HZ2, 21HZ1, 21HZ2 and 31HZ1); Fiberboard (11G); Wooden (11C, 11D and 11F); Flexible (13H1, 13H2, 13H3, 13H4, 13H5, 13L1, 13L2, 13L3, 13L4, 13M1 or 13M2).

Browse special provision IB8

IP2

When IBCs other than metal or rigid plastics IBCs are used, they must be offered for transportation in a closed freight container or a closed transport vehicle.

Browse special provision IP2

IP4

Flexible, fiberboard or wooden IBCs must be sift-proof and water-resistant or be fitted with a sift-proof and water-resistant liner.

Browse special provision IP4

Minimum test pressure (bar)	2.65
Minimum shell thickness	§ 178.274(d)(2)
Pressure-relief requirements	Normal
Bottom opening requirements	§ 178.275(d)(2)

Browse special provision T3

TP33

The portable tank instruction assigned for this substance applies for granular and powdered solids and for solids which are filled and discharged at temperatures above their melting point which are cooled and transported as a solid mass. Solid substances transported or offered for transport above their melting point are authorized for transportation in portable tanks conforming to the provisions of portable tank instruction T4 for solid substances of packing group III or T7 for solid substances of packing group II, unless a tank with more stringent requirements for minimum shell thickness, maximum allowable working pressure, pressure-relief devices or bottom outlets are assigned in which case the more stringent tank instruction and special provisions shall apply. Filling limits must be in accordance with portable tank special provision TP3. Solids meeting the definition of an elevated temperature material must be transported in accordance with the applicable requirements of this subchapter.

Browse special provision TP33

(8) Packing Authorizations (§173.***)

(8A) Exceptions	154	see 49 CFR §173.154
(8B) Non-bulk	212	see 49 CFR §173.212
(8C) Bulk	240	see 49 CFR §173.240

(9) Quantity Limits

(9A) Passenger aircraft/rail	15 kg
(9B) Cargo aircraft only	50 kg

(10) Vessel stowage

(10A) Location

Stowage category “A” means the material may be stowed “on deck” or “under deck” on a cargo vessel or on a passenger vessel.

Source: 49 CFR §172.101(k)

(10B) Other

40	see 49 CFR §176.84
53	see 49 CFR §176.84
58	see 49 CFR §176.84

Source: 49 CFR §176.84

Segregation chart for load, transport, and storage

This chart shows whether loading, transport, or storage with other hazard classes is permitted, prohibited, or restricted. Based on 49 CFR §177.848.

Note: In this segregation and separation chart are HazMat of hazard class 8 considered depending if there are liquid. Currently HazMat Tool is not able to to check if a HazMat is liquid or not. Therefore it is assumed as liquid. See PHMSA Interpretation #09-0252.

Hazard class	8	7	6.1	5.2	5.1	4.3	4.2	4.1	3	2.3B	2.3A	2.2	2.1	1.6	1.5	1.4	1.3	1.1/1.2
1.1/1.2
1.3
1.4
1.5
1.6
2.1
2.2
2.3A
2.3B
3
4.1
4.2
4.3
5.1
5.2
6.1
7
8

	Must not be loaded, transported, or stored together in the same vehicle or facility.
	May be loaded, transported, or stored together.
	May be loaded, transported, or stored together only with restrictions.

Similar substances

UN / ID	Proper shipping name	Hazard class
UN 3165	Aircraft hydraulic power unit fuel tank (containing a mixture of anhydrous hydrazine and monomethyl hydrazine) (M86 fuel)	3
UN 0508	1-Hydroxybenzotriazole, anhydrous, dry or wetted with less than 20 percent water, by mass	1.3C
UN 1382	Potassium sulfide, anhydrous or Potassium sulfide with less than 30 percent water of crystallization	4.2
UN 1385	Sodium sulfide, anhydrous or Sodium sulfide with less than 30 percent water of crystallization	4.2
NA 2845	Ethyl phosphonous dichloride, anhydrous pyrophoric liquid	6.1
UN 1726	Aluminum chloride, anhydrous	8
UN 2075	Chloral, anhydrous, stabilized	6.1
NA 2927	Ethyl phosphonothioic dichloride, anhydrous	6.1
UN 1048	Hydrogen bromide, anhydrous	2.3
UN 1463	Chromium trioxide, anhydrous	5.1
UN 1768	Difluorophosphoric acid, anhydrous	8
UN 1773	Ferric chloride, anhydrous	8
UN 1776	Fluorophosphoric acid anhydrous	8
UN 1050	Hydrogen chloride, anhydrous	2.3
UN 1052	Hydrogen fluoride, anhydrous	8